EPEC 2024 PDF

Epec CAN Module Family CONTROL MODULE G08 / MAN DOCUMENT VERSION HISTORY Date Notes Document . Epec provides software tools for control system programming, adjusting, and testing. From the systems engineering viewpoint, it is not enough to have sufficient. Open and compatible. Embedded control systems are based on PLCopen and CANopenĀ®, which make them easily scalable to meet requirements for both.

Author: Maut Vudozil
Country: Guadeloupe
Language: English (Spanish)
Genre: Technology
Published (Last): 19 May 2013
Pages: 373
PDF File Size: 6.61 Mb
ePub File Size: 10.74 Mb
ISBN: 440-1-94686-471-7
Downloads: 52331
Price: Free* [*Free Regsitration Required]
Uploader: Akidal

Protection for plugs depends on cable processing? In very carefully selected applications a pin of this type can also be used as an input 2204 using the output state monitoring feature.

Mounting position horizontal or vertical to allow water etc. This document contains necessary data concerning the module in question, which system designer needs in system development work. J only for one bus in the same module? It must be taken care 2204 system design that the output unintentionally switching to on state causes no harm to system.

EPEC controller Manual _Download Manual

Mining Machines Monitoring Functions Following issues can be monitored by the application? Violating this rating may lead to incorrect measurement or counting Note 7: Memory functions shall remain wpec A.

No saving operations program flashing or parameter storing into permanent memory can be done under 11,5 VDC. All functions return automatically to within normal limits after exposure is removed. The warranty does not cover possible expenses relating to travelling, accommodation, daily benefits, etc.

Nothing prevents using these pins to measure currents from other sources as well. In carefully selected applications these pins can also be used as digital inputs. For more information refer to programming manuals. Open loads can not be detected because the internal load resistor is connected to the ground. The pairing is done in application program. Inputs are divided into groups by the input impedance configuration.

Related Articles  RINOTRAQUEITIS FELINA PDF

Some of the inputs are grouped: These parameters depend on software cycle time Note 4: Violating this rating may lead to application program not noticing all input state transitions Epec Oy reserves all rights for improvements without prior notice Epec Oy Matinkatu 6 FIN Sein? IP67 classification according to IEC ? For example, if group two is configured as a current input, then both pins X3.

The shutdown circuit cuts off the power feed for the logic and loads in case of overvoltage. This illustrates the normal way to connect loads when load current measurement is desired. This makes it rather hard to estimate the actual maximum frequency of the pulses that the module is able to count reliably. A small and protective module casing keeps inside high performance microcontroller with lots of control capabilities. Pins of this kind can be used as e. Closed light cast aluminium housing?

Applies to inputs used for frequency measurement and pulse counting. There are two bit variables associated with each pin of this type in PLCopen programming environment.

CAN2 is user programmable? Box FIN Sein? All conditions must be respected. Module position Mounting base Mounting base Module position?

Powder-painted, hexavalent chromium free passivation for aluminium? With input voltages below 4,3 V it seems like the internal input resistance was connected to a 1,3 V voltage source Note 2: The manufacturer shall, at its sole option, repair the products at its manufactory in Sein? The second is one of the IX input bits for monitoring the actual state of the output or reading the pin as an input. CANopen for all physical buses? Gold plated, locked and sealed connectors: An external fuse should be installed for the product or the system power supply.

Related Articles  DIN 67530 PDF

2pcs EPEC 2024 ECU Plug 35 Car Waterproof Connector 776273 – 1 770680 – 1 and Termina

The buyer shall compensate the manufacturer to the extent that the manufacturer might be liable to pay damages epc a result of claims based on product liability according to paragraph above. The manufacturer will charge a scrapping fee from the buyer according to the manufacturer’s price list in force from time to time.

The result is a two channel pulse counter which is capable of detecting the direction of the movement of the sensor.

The other two are word variables in the IW memory area which hold the frequency value and the number of pulses. Violating this rating may lead to system not eepec all input state transitions. There are bits in IX area associated with these inputs to support the DI functionality. Is dependable for the other interrupt load in module for example heavy CAN-traffic can reduce maximum frequency. Copying of this document without permission is prohibited.

The shutdown circuit is activated when voltage reaches circa 32 V. So, the practical limits are lower but the maximum values of the table still give the basis for the estimation.